Enthoo EVOLV ATX TG
ATX Mid Tower
Side Panel Window
Tinted Tempered Glass
Power Supply Shroud
Front Panel USB
Motherboard Form Factor
- Micro ATX
- Mini ITX
Full-Height Expansion Slots
Half-Height Expansion Slots
Maximum Video Card Length
- 300 mm / 11.811" With Drive Cages
- 420 mm / 16.535" Without Drive Cages
Internal 2.5" Bays
Internal 3.5" Bays
- 180 points
- 31 months ago
from completed build RGB STALLION v2.1 Dual Loop/modded mania
This case should lose a star for the airflow issue BUT it makes up for it (in my opinion) with the generous amount of water cooling support! It made my loop assembly so much easier! You can easily compensate for the restrictive airflow with some beefy static pressure fans. That is what I did and my temps are great! It looks amazing and I love the minimalist approach to the design. The ties in the back for cable management made that a breeze and with rubber grommets on the interior it really helps clean up the overall look. Maybe it's form over function but I have to say it met my needs perfectly and is a truly gorgeous case!
- 159 points
- 38 months ago
from completed build Orion Unlocked
Beautiful, beautiful case. Lovely to build in, 10/10 would recommend to anyone, new builder or experienced.
- 125 points
- 37 months ago
from completed build StriX99
In my eyes, one of the highest quality, best looking cases on the market. It is very easy to build a super clean looking rig with this case. Good cable management capability and for the components there is much space to breath. Unfortunately it is not possible to remove the PSU-shroud (for swapping cables on the psu for example). The sliding 'fan/rad-mounting-grid' in the top is not the best solution for (thicker/sandwiched) radiators. There are several Tutorials how to use this limited space better. With one front mounted radiator not a problem at all. To bring down the temps a little more, I swapped the factory front with a custom front from mnpctech. The original almost closed front is not ideal but 'enough' for airflow.
- 84 points
- 29 months ago
from completed build Magnum Opus
Such a great looking case! It may be form over function because the airflow is far from the greatest BUT that can be easily compensated for with some beefy fans! Looks stunning though and the support for all things water cooling was a big factor for me!
- 45 points
- 33 months ago
from completed build RGB Everything!
Super expensive but an amazing case overall. Looks beautiful.
- 33 points
- 42 months ago
from completed build Pegasus
Despite two issues, the big aluminum Phanteks case is a pleasure to work in. It looks just as good as I imagined it would sitting up against my black tempered glass desk. Two windows means cable management needs a lot of attention, and the case helps with that through built-in wire straps and a large basement for hiding extra slack. However, with only one obvious cable routing path it would have been much easier to hold everything together if the straps were longer. As everything sits now they just barely stay velcroed together. Additionally, one of the two USB 3.0 ports on the front of the case is dead, which was a tad disappointing to find out after I had everything installed. Fortunately I don't use them often enough for it to be a real issue.
I will add a cooling discussion once I achieve a stable clock speed.
- 33 points
- 36 months ago
from completed build Aura Cypher
I love the aesthetic of this case, and the inclusion of RGB lighting control only makes it sweeter. The case is fairly easy to work with, though I will say it gets pretty tight against the backside after running all of the cables. Everything comes apart pretty easy, and there is plenty of airflow. The only complaint the I have is the top offset bracket. It's by no means a bad part, but it is really annoying to remove as it requires 5 screws, located on both sides of the case. This doesn't sound like a problem, until you need to move it in order to plug in a fan cable or move the lighting strip. Then it can become really annoying. If you're doing a build like this, be smarter than me. Don't screw the bracket back in until you have guaranteed that everything is running well.
- 33 points
- 36 months ago
from completed build 1440p gaming rgb build
I love the overall look of this case clean and beautiful. A few complaints 1. The thumb screws that hold the gpu in place are hard to get to 2. They could have included the four pin connector to connect the led on the case to the motherboard for the price
- 33 points
- 32 months ago
from completed build Mmm, dat glass - Phanteks Evolv ATX TG Gaming Build
In my opinion this is the best case on the market right now. Not only does it look amazing but it screams quality
- 32 points
- 35 months ago
from completed build Black and Blue (and RED all over!)
This case is ******* beautiful. All of the included cables come velcro managed across the back plate with room to spare for all the extra cables you'll have. Included radiator area that I'll eventually make use of. Glass panels are gorgeous.
- View Compatible CPU Coolers
- View Compatible Fan Controllers
- View Compatible Motherboards
- View Compatible Optical Drives
- View Compatible Power Supplies
- View Compatible Sound Cards
- View Compatible Storage
- View Compatible Video Cards
- View Compatible Wired Network Adapters
- View Compatible Wireless Network Adapters