PCPartPicker

  • Log In
  • Register

Build

Craziest (Workstation & Gaming)

by luka.volovec

221
115 Comments

Details

Date Published

May 26, 2017

Date Built

May 25, 2017

CPU Clock Rate

4.4 GHz

CPU Temperature While Idle

34.0° C

CPU Temperature Under Load

74.0° C

GPU Core Clock Rate

2 GHz

GPU Effective Memory Clock Rate

11.1 GHz

GPU Temperature While Idle

34.0° C

GPU Temperature Under Load

52.0° C

Description

Hey everyone!

Thanks for taking a look at my completed computer :). This is my first watercooled PC and I'm extremely happy with the finished product. I mainly use it for video editing, developing and gaming. It's been an ongoing project for the last month and a half.

EDIT: My build got featured!! :D Thank you to everyone who took a look and upvoted! I really enjoy browsing through this site and looking through builds, so to be featured means a lot. :) Cheers!

Build process

The build process went really well until I got into watercooling the components. I had a few problems here and there with bending and cutting the tubes correctly (I used acrylic), but towards the end I kind of got a hang of it. During my first leak test came the first larger problem - one of my 1080 Ti STRIX waterblocks was leaking because I had overtightened the screws on the terminal. A few days later I got a replacement (I'm from Slovenia so EKWB is practically around the corner) and changed the broken plexi glass. After that incident I was very careful when attaching the terminal again! :)

There were no leaks the second time around. However, the draining process was very interesting and took quite a while due to my inexperience! The only thing that's an issue now are the air bubbles stuck in the motherboard monoblock. I will let it run for a week or so to see if it fixes itself. Does anyone have an idea how to get rid of them (I can send you a picture)? I tried tilting, shaking the case, turning the pump on and off and similar but to no avail so far.

Watercooling

The choice for the custom loop primarily came with help from the EKWB configurator that tells you what you can fit in your case. From there I checked if the two radiators could fit. I'm using the PE series radiators. As you can see in the photos they can barely fit in the case, although it's still possible to mount the vertical radiator lower if you wanted too. I used a serial terminal to connect the GPUs insted of classing tubing because I really like the see-through effect it brings to the whole build, makes it look really special in my opinion. The pump/res combo used is the EK-XRES 140 Revo D5 PWM with sleeved cables. I'm really satisfied with all the custom parts.

The fan choice are the F3-120 PWM Vardar fans that run at 1850 rpm. They are very silent even at full load. Due to personal preference I decided to hide the fans behind the radiators, so the front radiator is in a push configuration and the top radiator is in a pull configuration. I configured the fans using the Fan Xpert tool in Ai Suite 3. That also calibrated the water pump that is connected to the CPU fan header for me. Overall the result is pretty good. It could use some tweaking around the 60 - 80 % load (liquid tends to get a bit warm).

Benchmarks

CPU @ 4.4 GHz at 34°C idle and 74°C at 100 % load, GPUs @ +60 MHz Core Clock and +400 MHz Memory Clock at 34°C idle and 52°C at 100 % load, Liquid is at 44°C during load. Falls to around 27°C if I let it run idle for an hour.

I will update this part with benchmarks as soon as I do them. Hoping to get top 100 on Time Spy (for the next month at least before all the new components come out)! :)

Notes

The SLI bridge used can be seen here. It can be connected to an RGB header on the motherboard to have it work with AURA Sync. You can also select the color by pressing on the logo on the bridge itself, which is super cool since you don't have to have extra cables running around in your PC.

Thank you to Ensourced for the amazing cable extensions - the colors match perfectly and the quality is outstanding. Couldn't be more happy.

Will write my reviews for all the parts I used in a short while.

Thank you again for taking a look and I hope you enjoyed the photos! :)

Part Reviews

CPU

Super expensive and I definitely overpaid. I hope that with the new competition from AMD, the prices for high-end processors will climb down. Got it working at 4.4 GHz, stable in games and in benchmarks. Does any task with ease. It's truely a beast CPU.

Motherboard

Overally a very good X99 motherboard for it's price if you compare it with other high-end ones. My only complaints are: only 2 fan headers along with CPU fan and only one reinforced PCI-E connector. You can clearly see that the second graphics card is bending more. I chose it because of it's ATX form factor and overall features.

Memory

Looks amazing and performs as listed. I chose the C14 timing variant because I had the budget for it. Sadly there is still no support for X99 boards, hence why it is running in rainbow mode - which actually looks amazing. It deserves 5 stars either way. Best looking RGB ram in my opinion.

Storage

Insane speeds and cable-free installation. Just plug it into a M.2 socket and it works. Note to anyone with M.2 SSDs and additional hard drives: I had to remove my other drives to make my computer boot to this drive. Keep that in mind. Games load in a matter of seconds. Definitely recommend this M.2 SSD with any amount of capacity.

Storage

I think this is a great deal for value, if you can support this kind of budget. Works as a replacement for an HDD drive in my case and there is plenty enough of capacity to store any kind of data. Performance is of course top notch as you would expect.

Video Card

Great graphics card, can be overclocked to higher clocks with original cooler. In my case I replaced the cooler with an EKWB waterblock but still could not hit higher clocks. So I definitely recommend this model for anyone looking to buy a 1080 Ti. LEDs look amazing. I can hear coil whine on my cards, but it should go away with time.

Case

Amazing looking case with sleek lines and big side panels from tempered glass. Keep in mind you need to keep your cables tidy since there is a window on both sides! Plenty of room for cable management and a large amount of rubber grommets so cable routing is a breeze.

Power Supply

Not much to say about this PSU, since it is without a doubt a top pick for the price. 80+ Platinum certificated, zero fan noise at low load, Corsair Link integration so you can check your power consumption at any time and great build quality. Recommended.

Monitor

This monitor looks amazing! Coming from 1080p with average colors and quality, I was literally shocked how good the colors look and how smooth everything is at this resolution. Gaming is a unique experience with wide viewing angles and 100 Hz. Depends on your taste, but I absolutely love the extra real estate for gaming and productivity.

Comments Sorted by:

mcgoff360 1 Build 5 points 21 months ago

wow, i love everything about this computer !! that sli bridge being clear is SO sweet. well done !! now if only my paycheck could afford that ... :(

MjolnirThunder 3 points 21 months ago

I assume you mean the clear waterblock for the GPU cooling, technically speaking the SLI bridge is the other part with Asus's ROG logo on it.

luka.volovec submitter 2 Builds 2 points 21 months ago

As MjolnirThunder said, I guess you mean the plexi terminal that's connecting the GPUs, and yeah, I definitely agree with you that it looks amazing :) Thank you!

mcgoff360 1 Build 3 points 21 months ago

haha yes, i meant the waterblock. the sli bridge is ... fine but the gpu terminal is definitely pretty sweet looking!!

dkatherton 2 Builds 3 points 21 months ago

Congratulations on a job well done! It feels good right? Great work on the bends, I can tell you put a lot of planning into the layout. I'm a fan of straight lines, simple bends and symmetry so I appreciate the 2x45 angled adapter, extender and other various fittings you used in your build. Enjoy it!

+1

luka.volovec submitter 2 Builds 2 points 21 months ago

Just took a look at your watercooled build and I have to say your bends look just perfect! Thanks for the kind words! :)

dkatherton 2 Builds 3 points 20 months ago

Thanks! I got lucky with the layout and things lined up nicely. Pretty simple bends but works out to a clean look.

Lyrix 2 points 21 months ago

DAMN!!!

WOW!!! 1+! This is amazing! It looks great! WOW WOW WOW!

luka.volovec submitter 2 Builds 2 points 21 months ago

Thank you ;)

Lyrix 1 point 21 months ago

you are very welcome!!!

DarthxxNecrosis 2 points 21 months ago

Wow, very impressive build. Definitely digging the water cooling system you setup for the rig.

luka.volovec submitter 2 Builds 2 points 21 months ago

Thanks! Took me a while to do the loop so the feedback is really nice :)

jabbacalvin 1 Build 2 points 21 months ago

Welp. this is for sure gonna get a feature!

luka.volovec submitter 2 Builds 2 points 21 months ago

Here's hoping haha :D Thanks!

dixonerfais 1 Build 2 points 21 months ago

I love that you spent more on EKWB parts than I did on my first build! This computer looks amazing, wish I had one of those Ti's! +1

luka.volovec submitter 2 Builds 3 points 21 months ago

Thank you!

llӇƳЄƝƛԼƠƦƊll 2 points 21 months ago

I want to afford this ;3; also a thing I saw someone do was mount the led part from the cooler onto the pcb, so if you need all the leds you should try it, looks pretty cool tbh :) great build btw

luka.volovec submitter 2 Builds 2 points 21 months ago

That sounds like a great idea, I'll give it a look. Thank you!

Experience 1 Build 2 points 21 months ago

How many frames do you need anyways 0-0

llӇƳЄƝƛԼƠƦƊll 1 point 21 months ago

More than how much it costs B)

Experience 1 Build 1 point 21 months ago

10 frames for every 100 bucks you mean B)

skyingram21 2 points 21 months ago

Pretty new to the site and just now building my first pc but this right here is one of the best looking builds I've ever seen. Amazing job man.

luka.volovec submitter 2 Builds 2 points 21 months ago

Thank you! Means a lot, really. :)

Yahtadi 2 points 21 months ago

Whoa

Yahtadi 2 points 20 months ago

And now you can run the entire universe!

luka.volovec submitter 2 Builds 1 point 20 months ago
Nater650 2 points 20 months ago

That build is overpowered

Justiceinacan 7 Builds 2 points 20 months ago

DAMN SON I LOVE THE LOOK OF IT

luka.volovec submitter 2 Builds 1 point 20 months ago

Thanks!

ISoloLlama 2 points 10 months ago

Epic you must have had a lot of spare money for this +1

CheekyPotato 1 point 21 months ago

Are you going to upgrade to skylake-X and x299 when that comes out?

luka.volovec submitter 2 Builds 4 points 21 months ago

Seeing as how this was a big investment I probably will not be updating so soon. It's a bit sad that all the news came like 2 weeks after I had ordered the computer. I guess that's how it is always with electronics. However, when new watercooling parts come out, I might consider it. Thanks for visiting! :)

Melganis 1 point 21 months ago

It is too bad. The Skylake X CPU's are not much of an upgrade, your performance is basically gonna be just as good. Where you are missing out is the new chipset. The X99 is missing some stuff. You pointed out a good example with the RGB RAM. Also, Thunderbolt 3 is trickier on the X99. Another example is the new MoBo's will have headers for USB 3.1 Gen. 2, so you can have type C on the front of the case, etc. Although, I am disappointed with how few cases are supporting front panel USB type C... they seriously need to start making some case updates across all the big manufacturers.

luka.volovec submitter 2 Builds 2 points 21 months ago

Yep, everything you pointed out should be noted. There is a lot of new features coming out on the new chipset that will be beneficial to the end user. I also hope that case producers will start implementing the new standards in their cases. Thanks for the info!

[comment deleted]
CheekyPotato 1 point 20 months ago

right since they would give 1-5 more fps

freefly32 1 point 20 months ago

Hey. That's not a bad increase just for a software update tbh :P

And just a few more tweaks, sorry ._.

[comment deleted by staff]
luka.volovec submitter 2 Builds 3 points 21 months ago

Yeah, I think so too.

Osiris.Rufus 1 point 21 months ago

Insane build! The only complaint I have( and it just the for the safety of parts) is that I cringe at acrylic. If you pull too hard on it it just breaks instantly. It's so much more scary than PETG tubing. But for the build itself no complaints, one of the best I've seen.

luka.volovec submitter 2 Builds 1 point 21 months ago

I was sure I was ordering PETG tubing from EKWB, but when it arrived I realised it was actually acrylic. During bending and cutting though, it did feel okay. I will be extra careful with acrylic though :) Thank you!

Skimby 1 point 21 months ago

Mastered to perfection...

luka.volovec submitter 2 Builds 1 point 21 months ago

Thanks!

Skimby 1 point 21 months ago

How does the SLI handle the ultrawide in gaming?

luka.volovec submitter 2 Builds 1 point 21 months ago

Benchmark tests aside, ultrawide gaming gets an increase from 10-40 % depending on the game. I even noticed downscaling in some cases. Results are similar to benchmarks done on this site. It really depends.

Skimby 1 point 20 months ago

Thank you!

Blacksm1le 1 Build 1 point 21 months ago

Very pretty work on a fierce beast +1

luka.volovec submitter 2 Builds 1 point 21 months ago

Thank you!

Melganis 1 point 21 months ago

This is dope. It looks beautiful. You did an outstanding job with maximizing the radiator capacity in a case that is really designed for a CLC/AIO cooler. Do you mind including a section in your part review about your custom loop? Describe the radiator choices, and why you used what where. Include info on fan choice. What RPM are your fans running? Did you set up custom fan curve? What is that SLI bridge, it looks real sexy. Why did you go for the EK terminal instead of just using hard tube between the blocks?

luka.volovec submitter 2 Builds 1 point 21 months ago

Thank you for the reply and questions! I updated the description with answers to your questions and more :) Hope it helps!

Melganis 1 point 21 months ago

Thanks for doing that, it was helpful. I wanna say, I have checked out tons of Enthoo Evolv ATX TG builds, and I can say, yours is the all around prettiest and most well done out of all of them. Before this build my favorite was done recently by Singularity Computers. He is an absolute animal, with modding skills and experience that puts him among the elite. You might want to check out his build--he is the only person I've seen fit dual loops in this case, and he manages to do it with huge reservoirs. He even squeezes a damn Aquero fan controller. His loop is much more complex than yours, because there's no monoblock, but the beauty of yours is just unmatched. https://www.youtube.com/watch?v=M_jc0tkIG_M&t=636s

luka.volovec submitter 2 Builds 1 point 20 months ago

Took a look, and that build is amazing, dual loop in this case. Love the metal tubing as well. Glad you think this is up to par looks wise! :)

Bassethnd7 1 Build 1 point 20 months ago

Don't you need more HD space for your stuff? 3 TB seems small in comparison to the system.

luka.volovec submitter 2 Builds 1 point 20 months ago

I'm using external hard drives to immediately transfer the data. Although I will be upgrading to another SSD in the near future.

dragoon20005 4 Builds 1 point 20 months ago

i am jelly at this build

the next project will prob be custom painting the casing.

kinda reminds me of JaysTwoCent Old Spice build for Terry Crews

luka.volovec submitter 2 Builds 1 point 20 months ago

A custom paint job would definitely bring even more to the build - maybe for the next project like you said :) I don't think this build is anywhere near that one, but thank you for the nice words!

dragoon20005 4 Builds 1 point 20 months ago

The next build you could try the upcoming AMD 16 core Treadripper monster cpu. The leaked prices of the upcoming Intel 14 core is still around 1600 USD. If the AMD 16 cores is just 1000 USD. Then it a no brainer the AMD will be the deal. A lot of my buddies got the Ryzen 7 1700 for the cores over the i7 7700k.

dragoon20005 4 Builds 1 point 20 months ago

Yup Intel just unwrapped their 18 core behemoth. 2000 USD a pop.

For that price thou i could prob buy 2 Treadrippers.

DocH 3 Builds 1 point 20 months ago

great build i did something similar. Only downside is i feel your top radiator takes up so much real estate when looking at it. Otherwise clean and well done. if you remove the radiator mount on top and take two long pieces of aluminum you can pull that top radiator up higher out of the way. it a common mod everyone does for this case.

luka.volovec submitter 2 Builds 1 point 20 months ago

I definitely agree with you. This was actually bothering me when I started putting all the watercooling parts in. I was expecting to be able to put the fans above the radiator mount, but couldn't. Now that you're mentioning it, that's definitely something I could have done for sure. Thanks for taking a look!

DocH 3 Builds 1 point 20 months ago

no problem. I did the same thing with my build. There are two ways to do it one involves modding the actual case and drilling holes. The other is easier and doesn't. if you interested let me know and i can explain it better.

luka.volovec submitter 2 Builds 1 point 20 months ago

Sure, I'd like to know, you can send me a message. Maybe some time in the future when I change whatever in this build or exchange the liquid in a year I can change the top radiator.

Jexyz 1 Build 1 point 20 months ago

actual insanity

+1 for one of the most plain badass PCs I've ever seen.

luka.volovec submitter 2 Builds 1 point 20 months ago

Thanks, really means a lot!

mrzoltowski 1 Build 1 point 20 months ago

Very nice indeed.

luka.volovec submitter 2 Builds 1 point 20 months ago

Thank you.

Ypres 1 point 20 months ago

your monitor cost $1 less than my whole build..... :(

GREAT BUILD!! THIS WILL LAST YOU FOR A LOOONG TIME

+1

luka.volovec submitter 2 Builds 1 point 20 months ago

Thank you, really. :)

MuchLinux6500 2 Builds 1 point 20 months ago

WowwowwowwowwowWowwowwowwowwowWowwowwowwowwowWowwowwowwowwowWowwowwowwowwowWowwowwowwowwowWowwowwowwowwowWowwowwowwowwowWowwowwowwowwowWowwowwowwowwowWowwowwowwowwow....... WOW. Amazing!

luka.volovec submitter 2 Builds 1 point 20 months ago

Thanks!

OllieManMan 14 Builds 1 point 20 months ago

Fantastic build! How long did it take you to save and plan for this?

luka.volovec submitter 2 Builds 2 points 20 months ago

My last build that I did for myself was 5 years ago. I was slowly saving up for a new build since then. With the saved up money and successful projects, I had the required budget in March 2017. Then I went ahead with choosing parts, planning it out for about a month. I completed the entire build without the watercooling in mid-April. Watercooling took a bit longer because of university and work obligations. So all in all, the build took about a month and a half with planning, if there we no delays. And thank you! :)

OllieManMan 14 Builds 1 point 20 months ago

Nice work. Good thing you waited for the 1080ti to pop. This truly is the top end.

luka.volovec submitter 2 Builds 1 point 20 months ago

Thank you again, took a look at your builds for some inspiration for upcoming smaller budget computers (and since you were featured before, I immediately recognized your name)! :)

Adrew24 1 Build 1 point 20 months ago

eye candy in a good way

luka.volovec submitter 2 Builds 1 point 20 months ago

Thank you :)

filmguy9 1 point 20 months ago

Next time get more rads because 74 for any cpu overclocked or not is bad.

luka.volovec submitter 2 Builds 1 point 20 months ago

Can't fit more rads unfortunately, not without modding the case. I was expecting lower temps - but I need to recheck the temperatures after all the water bubbles have cleared from the monoblock.

ArchiIsHere 1 point 20 months ago

Boy oh boy am I a fan of Monoblocks, no idea why won't people use them more often, that aside overall a fantastic build. Big +1.

luka.volovec submitter 2 Builds 1 point 20 months ago

Thank you very much!

Anyansayo 1 Build 1 point 20 months ago

What kind of games are you going to run on this machine? That is some of the best cable management that I have ever seen. The only cables that I can see from the pictures are the GPU power cords. That custom loop looks really good too. And also, what kind of FPS ranges are you getting on this? I can only imagine the smoothness that it will run anything.

luka.volovec submitter 2 Builds 1 point 20 months ago

I like to play single player games that really challenge any setup (right now that's Tomb Raider and replaying GTA V). I also do some CS:GO, OW, H1Z1, but those don't really stress this rig at any resolution. I am able to run almost any games at 144 Hz 1440p Widescreen. The lows can sometimes dip to 80, but since I'm using a G-Sync screen, everything looks super smooth. Thank you for your taking a look!

Anyansayo 1 Build 1 point 20 months ago

By the way, your build pictures look professionally photographed. Great clarity on all of them.

luka.volovec submitter 2 Builds 1 point 20 months ago

I'm using a Nikon D7100 with a pretty basic lens 18 mm - 140 mm f/3.5. I use it for photography every so often, but it's basically my camera for trips/events, etc. Glad you like the quality :)

Ricardo_Nixon 1 Build 1 point 20 months ago

Great build!... I'm still trying to find a build that isn't built in the Phanteks Enthoo Evolv ATX though....

Ricardo_Nixon 1 Build 1 point 20 months ago

Also, where'd u get that sli bridge damn dudee

Cazza_ 1 point 20 months ago

o.O thats awesome :)

jase10 3 Builds 1 point 20 months ago

Pure work of art... Dam GOOD!

bigg_critter 1 Build 1 point 20 months ago

all that is to be said is..beautiful! good for you my friend +juan

LordNermal 1 point 20 months ago

What is your job? And sick build +1

Gooberdad 10 Builds 1 point 20 months ago

Great looking powerhouse pc. Congrats on the featured spot. Thumbs up.

ImperiousBattlestar 1 point 20 months ago

Nice build, looks amazing. Totally lives up to its name. +1 :)

LonghornAlamo2040 1 point 20 months ago

Damn that's a very nice rig.

GG m9

zmac0135 1 point 20 months ago

Wow... +1... I am speechless lol. Nice part choices and attention to small details. This build is absolutely beautiful, especially for first time with water-cooling. Enjoy this powerhouse of a pc.

Sketch25 1 Build 1 point 20 months ago

Absolutely gorgeous build man! I have not seen many builds using the PVC serial block. I think it looks amazing, which is why I used it on my build. I will switch over to PETG here soon since I have all the parts. The flexible tubing was supposed to be temporary till all my parts showed up, but I ended up leaving it till I have a long weekend to bend tubes. Now that I see your build, it gives me more reason to start the bend process. I wish I would have went with this case, but so many people have it. Yours really stands out though and you should be very proud of your build. Thank you for making my day with perfection! Congrats on the feature btw :)

xDiiThy 3 Builds 1 point 20 months ago

what the crap mad bhuldlddd

AION-MC EKWB 18 Builds 1 point 20 months ago

Love everything about this! Great job!

Vinnan 1 Build 1 point 20 months ago

I feel REALLY BAD for you:

The X series or processors just released

JCMsergox 4 Builds 1 point 20 months ago

Holy crap...

Durzantion 1 point 20 months ago

This build is amazing seriously well done :D, one recommendation the other colours on the R.A.M throw the colour scheme a lot if you can set them to be solid on that awesome icey blue you got going the build will be perfect! +1

ivannooz 14 Builds 1 point 20 months ago

that's pretty detailed build you have there sir i love it! that cpu though is crazy expensive!

seanbarkley 2 Builds 1 point 20 months ago

Woah dude! This build is PERFECTION!!

Kudos!

TheCy-FiJuggernaut 1 point 20 months ago

Why is the CPU waterblock so big? It looks like it's made for Threadripper!

OatmealMemePie 1 point 11 months ago

I would be so scared to own any pc this expensive. If my house was to ever burn down i would grab the pc before anything else.

ISoloLlama 1 point 10 months ago

also how many fps do you get on games

luka.volovec submitter 2 Builds 1 point 10 months ago

I can run almost any game on max settings. I am using a 165 Hz 1440p monitor and can get around 120-165 fps in most AAA games.

Alhen 1 point 8 days ago

You have the most beautiful assembly in this building, which I saw! Please write what models of PE radiators are installed?

[comment deleted]
[comment deleted]
[comment deleted]
[comment deleted]
[comment deleted by staff]
[comment deleted]
luka.volovec submitter 2 Builds 1 point 20 months ago

Thank you! :)

[comment deleted]
[comment deleted]
luka.volovec submitter 2 Builds 1 point 20 months ago

You mean these ones? Thank you!

[comment deleted]
luka.volovec submitter 2 Builds 1 point 20 months ago

Haha yeah, I've been trying to overclock my card for like 2 days now (reason I haven't uploaded scores), because I can't, just can't get it over 2000 MHz. I've tried adding 100 % voltage, maxed the power limit, incrementing by like 2 MHz.. nothing works. It just freezes, downclocks back to 2000 MHz and stays there... I can only get the memory to go higher. Maybe I can try overclocking each card on it's own but I really don't want to :D

Sketch25 1 Build 1 point 20 months ago

OK, I thought I was the only one having issues trying to OC my 1080 Ti's. Everything I try causes my system to freeze.

[comment deleted]
luka.volovec submitter 2 Builds 1 point 20 months ago

Yeah, it's bothering me a bit. But yeah, benchmarks aside, in games there isn't a noticeable difference, so I'm not really complaining :)

[comment deleted]
luka.volovec submitter 2 Builds 1 point 20 months ago

Probably not but I took a look at the card you mentioned :)

[comment deleted]
[comment deleted by staff]
luka.volovec submitter 2 Builds 2 points 21 months ago

Yeah, I think I got very lucky with the CPU. My GPUs on the other hand don't really appreciate additional overclocking :D Thank you.

[comment deleted by staff]
luka.volovec submitter 2 Builds 2 points 21 months ago

Thank you! :D

[comment deleted by staff]
luka.volovec submitter 2 Builds 1 point 21 months ago

Total overkill aside, I do 4k video rendering and 360 degrees video compositions, along with program workflows in Visual Studio plus mobile development. But this is without a doubt a special project that I did for myself. Thanks for taking a look :)

[comment deleted by staff]
[comment deleted by staff]
luka.volovec submitter 2 Builds 1 point 20 months ago

Oh it's definitely swimming yup :)

[comment deleted by staff]